因有些模型數據計算量大,影響交易速度,因而設想通過一臺計算機計算結果存入數據庫,另一臺電腦讀取結果進行判斷下單.

以計算布林通道為例:

建立數據庫CTZB公式:

DATABASE('Provider=Microsoft.Jet.OLEDB.4.0;Data Source=c:\asset.mdb');
DBEXECUTE('create table ctzb(stockdate date,ma4680 double,up4680 double,low4680 double)');

寫庫公式如下:

DATABASE('Provider=Microsoft.Jet.OLEDB.4.0;Data Source=c:\asset.mdb');
stdp30:=2*stdp(close,4680);
ma30:ma(close,4680);
up30:=ma30+stdp30;
down30:=ma30-stdp30;
T0:=NUMTOSTR(DYNAINFO(207),0);
T01:=STRCAT(NUMTOSTR(hour,0),':');
T02:=STRCAT(NUMTOSTR(minute,0),':');
T1:=STRCAT(STRCAT(T01,T02),STRRIGHT(T0,2));
D0:=NUMTOSTR(DATE,0);
D01:=STRCAT('20',STRMID(D0,2,2));
D02:=STRCAT('-',STRMID(D0,4,2));
D03:=STRCAT('-',STRMID(D0,6,2));
D1:=STRCAT(STRCAT(D01,D02),D03);
DAY11:=STRCAT(STRCAT(D1,' '),T1);
DAY01:=STRCAT(char(39),DAY11);
DAY1:=STRCAT(DAY01,char(39));
if ma30<>ref(ma30,1) or up30<>ref(up30,1) or down30<>ref(down30,1) then begin
DBEXECUTE('insert into ctzb(stockdate,ma4680,up4680,low4680) values(cdate('&day1[DATACOUNT]&'),'&numtostr(ma30[DATACOUNT],3)&','&numtostr(up30[DATACOUNT],3)&','&numtostr(down30[DATACOUNT],3)&')');
end
DRAWTEXTEX(1,1,50,0,''&day1[DATACOUNT]&'',colorred)；

讀庫公式:

DATABASE('Provider=Microsoft.Jet.OLEDB.4.0;Data Source=c:\asset.mdb');
//檢索數據庫表
DBTABLE('Select * From ctzb Order By StockDate');
//讀取STOCKCLOSE字段數據
mid:DBVALUE('ma4680');
up:DBVALUE('up4680');
DOWNVOL:DBVALUE('low4680');

問題:1.寫庫時有很多相同的記錄無法過濾.

       2.讀庫要約5秒鐘才會刷新一次,放回同一臺機子的金字塔也是這樣.

看看能否解決,萬分感謝!!

ctzb stockdate ma4680 up4680 low4680 2014-05-08 15:03:30 2148.328 2165.552 2131.104 2014-05-08 15:03:30 2148.328 2165.552 2131.104 2014-05-08 15:06:19 2148.252 2165.541 2130.963 2014-05-08 15:06:19 2148.252 2165.541 2130.963 2014-05-08 15:06:21 2148.248 2165.54 2130.956 2014-05-08 15:06:21 2148.248 2165.54 2130.956 2014-05-08 15:06:23 2148.248 2165.54 2130.956 2014-05-08 15:06:23 2148.248 2165.54 2130.956 2014-05-08 15:06:25 2148.248 2165.54 2130.956 2014-05-08 15:06:25 2148.248 2165.54 2130.956 2014-05-08 15:06:27 2148.248 2165.54 2130.956 2014-05-08 15:06:27 2148.248 2165.54 2130.956 2014-05-08 15:06:29 2148.248 2165.54 2130.956 2014-05-08 15:06:29 2148.248 2165.54 2130.956 2014-05-08 15:06:31 2148.243 2165.539 2130.948 2014-05-08 15:06:31 2148.243 2165.539 2130.948 2014-05-08 15:06:33 2148.243 2165.539 2130.948 2014-05-08 15:06:33 2148.243 2165.539 2130.948 2014-05-08 15:06:35 2148.243 2165.539 2130.948 2014-05-08 15:06:35 2148.243 2165.539 2130.948 2014-05-08 15:06:37 2148.243 2165.539 2130.948 2014-05-08 15:06:37 2148.243 2165.539 2130.948 2014-05-08 15:06:39 2148.244 2165.538 2130.949 2014-05-08 15:06:39 2148.244 2165.538 2130.949

很多記錄相同的,但無法過濾(用時間,價格等條件作判斷后再寫入)

http://www.weistock.com/bbs/dispbbs.asp?boardid=5&Id=64723

請看該貼的回復,范例上已經用超全局變量控制了,在逐K線模式下最后K線工作,只有出一根新K線才寫庫