請高手幫忙修改　[金字塔]

A1:=REF(H,8)=HHV(H,2*8+1);
B1:=FILTER(A1,8);
C1:=BACKSET(B1,8+1);
D1:=FILTER(C1,8);{高點}
R11:=BACKSET(ISLASTBAR,BARSLAST(D1)+1); S11:=R11>REF(R11,1);
DRAWLINE(D1,H,S11,H,1),COLORBLUE;
A2:=REF(L,8)=LLV(L,2*8+1);
B2:=FILTER(A2,8);
C2:=BACKSET(B2,8+1);
D2:=FILTER(C2,8);{低點}
T11:=BACKSET(ISLASTBAR,BARSLAST(D2)+1); U11:=T11>REF(T11,1);
DRAWLINE(D2,L,U11,L,1),COLORBLUE;
M:=INTPART(3*8/5);
A12:=REF(H,M)=HHV(H,2*M+1);
B12:=FILTER(A12,M);
C12:=BACKSET(B12,M+1);
D12:=FILTER(C12,M);{高點}
R112:=BACKSET(ISLASTBAR,BARSLAST(D12)+1); S112:=R112>REF(R112,1);
DRAWLINE(D12,H,S112,H,1),COLORRED;
A22:=REF(L,M)=LLV(L,2*M+1);
B22:=FILTER(A22,M);
C22:=BACKSET(B22,M+1);
D22:=FILTER(C22,M);{低點}
T112:=BACKSET(ISLASTBAR,BARSLAST(D22)+1); U112:=T112>REF(T112,1);
DRAWLINE(D22,L,U112,L,1),COLORRED;
VAR1111:=BACKSET(REF(HIGH,2)=HHV(HIGH,5),3);
VAR2222:=CROSS(VAR1111,0.9);
VAR3333:=BACKSET(REF(LOW,2)=LLV(LOW,5),3);
VAR4444:=CROSS(VAR3333,0.9);
壓力:= REF(HIGH,BARSLAST(VAR2222));
STICKLINE(CLOSE,REF(HIGH,BARSLAST(VAR2222)),REF(HIGH,BARSLAST

(VAR2222)),0.5,1),COLOREA91B5,LINETHICK3;
支撐:= REF(LOW,BARSLAST(VAR4444));
STICKLINE(CLOSE,REF(LOW,BARSLAST(VAR4444)),REF(LOW,BARSLAST

(VAR4444)),0.5,1),COLOR00B4FF,LINETHICK3;
下檔線:=(((CLOSE - LLV(LOW,13)) / (HHV(HIGH,13) - LLV(LOW,13))) *

100);
RRRSV:=SMA(下檔線,3,1);
KKK:=SMA(RRRSV,3,1);
DDD:=((3 * RRRSV) - (2 * KKK));
JJ12:=(((CLOSE - LLV(LOW,55)) / (HHV(HIGH,55) - LLV(LOW,55))) *

100);
RSV24:=SMA(JJ12,3,1);
K24:=SMA(RSV24,3,1);
D24:=((3 * RSV24) - (2 * K24));
壓力2:=IF(CROSS(D24,DDD),HIGH,REF(HIGH,BARSLAST(CROSS

(D24,DDD)))),COLORFFFFFF;
壓力位:=IF(ISLASTBAR,壓力2,DRAWNULL);
STICKLINE(ISLASTBAR ,壓力位,壓力位,120,0),LINETHICK4,COLORFFFFFF;
底部:=LLV(HIGH,30),COLOR00FF00;
底部位:=IF(ISLASTBAR,底部,DRAWNULL);
STICKLINE(ISLASTBAR ,底部位,底部位,100,0),LINETHICK4,COLOR00FF00;

請高手幫忙修改得再細致一些.      這是一分鐘的K線.      用來玩炒單的...

VAR1111:=BACKSET(REF(HIGH,2)=HHV(HIGH,5),3);
VAR2222:=CROSS(VAR1111,0.9);
VAR3333:=BACKSET(REF(LOW,2)=LLV(LOW,5),3);
VAR4444:=CROSS(VAR3333,0.9);
壓力:= REF(HIGH,BARSLAST(VAR2222));
STICKLINE(CLOSE,REF(HIGH,BARSLAST(VAR2222)),REF(HIGH,BARSLAST
(VAR2222)),0.5,1),COLOREA91B5,LINETHICK3;
支撐:= REF(LOW,BARSLAST(VAR4444));
STICKLINE(CLOSE,REF(LOW,BARSLAST(VAR4444)),REF(LOW,BARSLAST(VAR4444)),0.5,1),COLOR00B4FF,LINETHICK3;
下檔線:=(((CLOSE - LLV(LOW,13)) / (HHV(HIGH,13) - LLV(LOW,13))) *
100);
RRRSV:=SMA(下檔線,3,1);
KKK:=SMA(RRRSV,3,1);
DDD:=((3 * RRRSV) - (2 * KKK));
JJ12:=(((CLOSE - LLV(LOW,55)) / (HHV(HIGH,55) - LLV(LOW,55))) * 100);
RSV24:=SMA(JJ12,3,1);
K24:=SMA(RSV24,3,1);
D24:=((3 * RSV24) - (2 * K24));
壓力2:=IF(CROSS(D24,DDD),HIGH,REF(HIGH,BARSLAST(CROSS(D24,DDD)))),COLORFFFFFF;
壓力位:=IF(ISLASTBAR,壓力2,DRAWNULL);
STICKLINE(ISLASTBAR ,壓力位,壓力位,120,0),LINETHICK4,COLORFFFFFF;
底部:=LLV(HIGH,30),COLOR00FF00;
底部位:=IF(ISLASTBAR,底部,DRAWNULL);
STICKLINE(ISLASTBAR ,底部位,底部位,100,0),LINETHICK4,COLOR00FF00;

還是不夠理想...